| Customization: | Available |
|---|---|
| After-sales Service: | Warranty Certificate |
| Warranty: | 12 Months |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
The panel can be customized in English version.
★ With over-current, over-voltage, overheating automatic protection function;
★ With DC withstand voltage, impact discharge function;
★ The high-voltage pulse output is uniform and controllable;
★ Super short-circuit protection function, which can make the high-voltage output directly short-circuit to the ground;
★ It has dual 2.5-level pointer meters for current and voltage display, which is intuitive and clear, and it is clear at a glance whether the fault point is fully discharged, and the discharge process is reflected in real time;
★ High-voltage side voltage measurement, real-time and accurate;
★ With zero start protection and potentiometer zero output function, it is safe and reliable;
★ Unique high-voltage measurement design, in the stop state, the voltmeter can indicate the capacitor voltage in real time;
★ The discharge time can be arbitrarily set within the appropriate interval;
| Impact high voltage | 0-12KV |
| High voltage partial pressure | Voltage Accuracy 2.5 grade |
| Built-in capacitor | 12μF |
| Working power | AC 220V ± 10% 50Hz ± 2Hz |
| Discharge power | 0-864 J |
| Ambient temperature | -20 ~ + 50 ºC |
| Impact time | 3 ~ 7seconds |
| Impact power | 400W |
| Over current protection | 8mA (more than 3 seconds) |
| Over temperature protection | 85 ºC |
| Volume/size | 420L × 325W × 480(mm) |
1. Safety ground: The ground of the instrument shell must be reliably connected to the ground in order to prevent the instrument shell from being electrified or electric shock to personnel.
2. High-voltage ground: Also known as high-voltage tail, it must be grounded reliably to prevent high-voltage leakage and discharge. Poor contact may cause failure to boost the voltage, high voltage breakdown of the internal components of the instrument, and safety accidents caused by leakage or discharge inside the instrument.
3. Sampling ground: The negative terminal of the pulse energy storage capacitor has a high voltage and must be grounded reliably. It is used for sampling when the waveform is sampled under the high-voltage flashover state of the cable fault tester. (Without high-voltage flashover sampling, reliable grounding is still required).
4. Discharge button: Press this button to make contact with the ball gap, and discharge manually. (The duration of each key press cannot exceed 1s).
5. High voltage start button: When the start button light is on, it means that the voltage output is in the zero position. When the light is on, the start button is valid. If the start button light is not on after turning on the power switch, turn the voltage adjustment knob counterclockwise until the light is on. When the button light is on, press this button to start the device and generate high voltage output.
6. High-voltage stop button: When the test is completed or an abnormality occurs, press this button to cut off the high-voltage output, the high-voltage light goes out, and the internal discharge ball stops working. When the stop key is on, it means there is high voltage output, and when it is off, it means there is no high voltage output.
7. Over-current protection switch: When pressed, it means that the over-current protection function has started; when it is popped up, it means that the instrument has triggered the over-current protection.
15. High-voltage output (EMP): When impacting discharge, connect the high-voltage output line.
16. High voltage output (DC): When DC withstand voltage, connect the high voltage output line.
----------------------------------------------------------------------------------------------------------------
Packing list
Welcome you contact us for more information
------------------------------------------------------------------------------------------------------------------------------------
Packaging: Wooden case filled with foam
Shipping: by Air, Sea, Express, etc.
Shipping time: 7-15 days if it's in stock.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Application
A: We are factory.
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock,
it is according to quantity.
A: Payment<=1000USD, 100% in advance.
){kind=link}